Expanded Product Range with Tower Light Series
IT40S, IT50S and IT60S Open Network Capable Tower Light

model:IT40S, IT50S and IT60S

IT40S IT50S IT60S
     
  • Energy saving, maintenance free LED lights
  • Direct Ethernet and CC-Link control saves wiring
    and cost

  • Bright and even illumination thanks to M-System’s original reflection system
  • Number and color of LED modules can be freely combined.
  • IP 65

Wire Saver Tower Light

The IT40S, IT50S and IT60S Series are preassembled tower lights of 40-mm, 50-mm and 60-mm diameter LED modules. They feature direct control by PLC via Ethernet Modbus/TCP (model: ITxxSRE) or CC-Link (model: ITxxSRC).

In combination with M-System’s remote I/O modules, local discrete signals can trigger the light modules connected with single network cables via a remote PLC, saving a great part of parallel wiring from sensor devices to the PLC’s input cards, and from the PLC’s output cards to the lights.

Contact input type (ITxxSA1) without network connection is also available for local control.

 

Application Example with Network Capable Tower Lights

Application Example with Network Capable Tower Lights
 
 

Component Identification

Component Identification

Triple-Reflection System

M-System’s original triple-reflection design prevents the LED lights from wasteful diffusion and ensures effective and even lighting in obliquely downward directions.

 

Setting Panel & Status Indicator LED

DIP switches on the side are used to select blinking frequency (2 Hz or 10 Hz), alert sound (buzz) ON/OFF frequency, loudness level and to specify either the lights should be turned off or maintained in case of communication failure.

Power and network status indicator LEDs are also provided on the side.

 

Network Connection

RJ-45 connector for Ethernet or a separable tension-clamp terminal block for CC-Link is provided at the bottom of the tower for easy wiring.

 

Five-layer, Five-color LED Modules in Free Combination

Number of LED module layers can be specified from one to five when ordering. Five colors (red, amber, green, blue and white) can be freely combined for each module.

 
Five-layer, Five-color LED Modules in Free Combination
 
 
SELECTION GUIDE
EXTERNAL INTERFACE MODEL LIGHT MODULES SPEC
DIAMETER LAYER COLOR
Modbus/TCP Ethernet IT60SRE φ60 mm (2.36”) 1 to 5
Selectable
Red
Amber
Green
Blue
White

Selectable
PDF
IT50SRE φ50 mm (1.97”) PDF
IT40SRE φ40 mm (1.57”) PDF
CC-Link IT60SRC φ60 mm (2.36”) PDF
IT50SRC φ50 mm (1.97”) PDF
IT40SRC φ40 mm (1.57”) PDF
Contact input IT60SA1 φ60 mm (2.36”) PDF
IT50SA1 φ50 mm (1.97”) PDF
IT40SA1 φ40 mm (1.57”) PDF
 
GENERAL SPECIFICATIONS
Degree of protection IP 65, vertical mounting only (except the bottom connectors)
Connection
Power input
Contact input
Network

UL 1007 AWG 20
UL 1007 AWG 22 (ITxxSA1)
RJ45 connector (ITxxSRE)
Separable tension-clamp terminal (ITxxSRC)
Housing material
Tower
Lens

Flame-resistant resin (white)
Flame-resistant resin (transparent)

DIP SW Light's blinking frequency, buzzing ON/OFF frequency and volume level,
output at communication failure
LEDs Red, Amber, Green, Blue, White LED, continuous or intermittent
(approx. 2 Hz or 10 Hz)
Status indicators Power, Run, Link, Link100, COL (ITxxSRE)
Power, Run, Error, SD, RD (ITxxSRC)
Buzzing Approx. 3.3 kHz, continuous or intermittent (approx. 2 Hz or 10 Hz)
 
NETWORK SPECIFICATIONS
ITxxSRE: Modbus/TCP (Ethernet)
Standard IEEE 802.3u
Transmission 10BASE-T / 100BASE-TX
Baud rate 10/100 Mbps (Auto Negotiation)
Data format RTU (binary)
Port No. 502
Cable 10BASE-T: STP cable, category 5
100BASE-TX: STP cable, category 5e
Max. segment length 100 meters
IP address 192.168.0.1 (factory set); modifiable with PC Configurator Software
ITxxSRC: CC-Link
CC-Link Ver. 1.10
Device type Remote I/O station
Occupied node 1 station
Station No. setting 1 to 64 (selectable with rotary switch)
Baud rate 156 kbps, 625 kbps, 2.5 Mbps, 5 Mbps, 10 Mbps
(selectable with rotary switch)
Cable As specified by Mitsubishi Electric
 
CONTACT INPUT SPECIFICATIONS
ITxxSA1: Contact input
Contact input Dry contact, open collector (PNP/NPN)
Input resistance Approx. 50k ohms
ON 4 V or less / 10k ohms or less
OFF 20 V or more / 100k ohms or more
 
INSTALLATION
Power input
AC
DC

100-240 Vac (not available for ITxxSRE)
24 Vdc ±10% (ripple 10%p-p max.)
Operating temp -10 to +55 °C (14 to 131 °F)
Operating humidity 30 to 90% RH (non-condensing)
Atmosphere No corrosive gas
Mounting Surface (vertical direction only)
Weight 650-750 g (1.43-1.65 lbs)
 
PERFORMANCE
Insulation resistance 100M ohms or more with 500 Vdc
Dielectric strength 1500 Vac @1 minute (network to power to FE1; Ethernet/CC-Link)
1500 Vac @1 minute (input to power to FE1; contact input with AC power)
CE conformity EMC Directive (2004/108/EC)
EN 60947-5-1: 2004 + A1: 2009
Low Voltage Directive (2006/95/EC)
EN 60947-5-1: 2004 + A1: 2009
Terminal access protection VDE 0660-514 (finger protection)
 
MOUNTING POLE (option)
Model: ITPL
Pole with L-shape bracket Pole with mounting base
Pole with L-shape bracket Pole with mounting base
Product Bulletins (IT40S, IT50S, IT60S)
A4: PDF Letter: PDF
   
Page top